Glidden^® Stucco & Masonry Exterior Paint

Area Preparation:

All surfaces must be sound, dry, clean and free of oil, grease, dirt, mildew, form release agents, curing compounds, loose and flaking paint and other foreign substances.

NEW SURFACES:

Stucco, Concrete and Masonry - Cure at least 30 days before painting. pH must be 10.0 or lower. Roughen slick poured or precast concrete and remove sealers by chemical cleaning or abrasive method such as sandsweeping. Rinse thoroughly with water and allow to dry. Remove loose aggregate. Prime with this product or GLIDDENTM GRIPPER^® GL3210 acrylic primer. Fill masonry block with GLIDDENTM ULTRA-HIDE^® GL3010 latex block filler.

Interior Drywall - Prime with this product, GLIDDENTM GRIPPER^® GL3210 acrylic primer or GLIDDENTMGL1050 PVA latex primer. Wood - Prime with GLIDDENTM GRIPPER^® GL3210 acrylic primer. Caulk with latex-type caulk.

Preprimed and Unprimed Hardboard - Prime entire surface and all edges with GLIDDENTM GRIPPER^® GL3210 acrylic primer. Caulk with latex-type caulk. Steel - Prime with a metal primer.

Galvanized Metal and Aluminum - Prime with GLIDDENTM GRIPPER^® GL3210 acrylic primer.
PREVIOUSLY PAINTED SURFACES: Wash to remove contaminants. Rinse thoroughly with water and allow to dry. Dull glossy areas by light sanding. Remove sanding dust. Remove loose paint. Scrub heavy chalk areas and overhead (exterior) areas such as eaves with soap and water. Remove all mildew by washing with a solution of 16 oz (473 mL) liquid household bleach and two oz (59 non-ammoniated liquid detergent per gallon (3.785 L) of water. Rinse surfaces clean with water and allow to dry for 24 hours. Prime bare areas with primer specified under NEW SURFACES.

Weathered Aluminum and Vinyl Siding - Remove dirt and chalk. Prime with this product. If chalk remains after cleaning, prime with an acrylic primer (6001, 3210 or GL3210). Do not repaint vinyl siding with colors darker than the original color; the siding may warp. mL) non-ammoniated liquid detergent per gallon (3.785 L) of water. Rinse surfaces clean with water and allow to dry for 24 hours. Prime bare areas with primer specified under NEW SURFACES.

Weathered Aluminum and Vinyl Siding - Remove dirt and chalk. Prime with GLIDDENTM GRIPPER^® GL3210 acrylic primer. Do not repaint vinyl siding with colors darker than the original color; the siding may warp.

NOTE: Blistering and peeling of exterior house paints down to bare wood is usually caused by moisture behind the paint film. Moisture pressure forces the paint away from the surface. Sources of excess moisture in the wood must be eliminated prior to repainting to obtain normal service life of these paints. Old, unsound multiple coat paint systems may be subject to peeling when repainted due to the added weight and stress created by the paint layers. In such cases, all old paint layers must be removed back to the bare wood before repainting.

Application:
 
Mix thoroughly before use. May be applied by brush, roller or spray. No thinning required. For airless spray
application, use .015-.017” tip. Adjust pressure as needed. Do not apply when the surface or air temperature is below 50°F (10°C) or when temperatures are expected to drop below 50°F (10°C) within 48 hours of application. Do not apply if rain, snow or lower temperatures are expected within 48 hours.

Application Temperature:

Do not apply when the surface or air temperature is below 50°F (10°C) or when temperatures are expected to drop below 50°F (10°C) within 48 hours of application

Drying Time:

77°F (25°C) & 50% RH:
To touch – 1 hour To recoat – 4 hours

Coverage:

Apply at 300-400 sq ft/gal (7-10 m2/L). Actual coverage may vary depending on substrate and application method.

Cleanup: 

Soap and water
 
Recommended Substrates:

Ideal for use on properly prepared masonry, concrete, stucco, wood, weathered aluminum siding, weathered vinyl siding, drywall and sound painted surfaces. May be used self-priming on masonry and drywall.

Warning: 

Please refer to the Product Label, Technical Data Sheet (TDS) or Safety Data Sheet (SDS) for safety and detailed application instructions.